Disclosure: Bear in mind that some of the links in this post are affiliate links and if you go through them to make a purchase I will earn a commission. Keep in mind that I link these companies and their products because of their quality and not because of the commission I receive from your purchases.
Jun 162015

Samsung refrigerators have a diagnostics mode. The fastest and easiest way to access diagnostic mode is by pressing the top left and top right button in at the same time and holding for a few minutes. This will send the refrigerators on board computer into a pre programed diagnostic mode. If any error codes have been stored in the computer it will be displayed at this point.

If no error codes are displayed, you’ll see 88 88 all the segments will be full. When a samsung refrigerator error code is displayed one of the small lines or segments will be flashing and the rest of the 88 will disappear.  You will usually get the #2 error code for the ice maker sensor.

Samsung does not use a normal ice maker. Nothing about these refrigerators are normal though. They use a small sensor that tells the ice maker when the water has actually frozen. One the water freezes the ice maker needs to harvest it so it can call for water and fill again. This process usually takes between 2-4 hours. Every 2-4 hours the ice maker should be cycling on it’s own. Several things can cause slow ice production but for this article lets stick to the ice maker sensor error code..

Samsung Refrigerator Ice Maker Sensor Error:

The #2 error usually indicates an issue with the ice maker sensor. The sensor runs from the front of the ice maker where the timer motor is located to the bottom of the flex mold. Samsung and LG are known for their flex tray designs. Even Frigidaire has released their version of the flex tray. The sensor is a lot more accurate than a normal bi metal that’s found in a conventional Whirlpool style ice maker assembly.

Usually when this fault code is displayed the ice maker timer assembly will need to be replaced. Look on the bottom of the mold for a thin wire that goes to a bullet snapped plastic piece. Yes, that plastic piece is the actual sensor. The small plastic clip on the bracket usually breaks off. When that happens the sensor will fall down and it will eventually get crushed and broken. The wire will normally get cut in half. I’ve seen it countless times. Depending on your model you can get just the timer assembly and others you have to replace the ice maker as an assembly.

The ice maker on most of these units are mounted in the freezer on the left side. The ice maker has a small plastic facia that must be popped off. There’s a small clip that holds the plastic piece to the front of the ice maker. Gently pull out the cover will pop off. You will then see straight up there’s two holes. Up inside is two screws. Once the screws are removed the ice maker will slide forward and hand by the wire harness. The harness has a small tab that needs to be depressed in order for the molex connector to unplug. It’s actually very straight forward to fix this error code. The repair is not very complicated more time consuming.

Have a Samsung Refrigerator Error Code Question? Use the comment form below and I’ll try my best to help you fix your refrigerator yourself.



  4 Responses to “Samsung Refrigerator Ice maker Sensor Error Code”

  1. Hello. I have a Samsung model RF25HMEDBSR/AA03 with an ice maker ( at upper left) that will not stop making ice. It was purchased in 2014. The ice maker has no shutoff arm, but instead has a sensor at the back I believe. I have reset the icemaker using the reset button. Unplugged the refrigerator briefly to try and reset it, and made sure what appears to be the sensor is clear of ice. Nothing has worked, and there are no error codes showing. Any suggestions would be appreciated.

  2. I have a Samsung R265. The fridge temperature will not change down to a lower . I push the button down to 38 but it doesn’t move and remains at 53. I did analysis test and the top right bar of the 8 was flashing which I thought was the ice maker sensor. Would that effect the fridge. The problem started after moving the fridge. Thoughts ?

  3. Hallo. I have a problem with Samsung RSG5PCRS. My sidebyside is not working correctly now.
    Freezer switches off when it reaches the optimal temperature of -19 degrees.
    The error code displays, and the manual says it means “Ice maker function error/Ice ejection trouble”.
    Can you help me?

 Leave a Reply

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>